.
Architectural Production Software 2005

 

Msg # Alert / Error Message  
1 Sorry, you must have an internet connection to be able to send a bug report / suggestion / question or problem / tip or trick / alternate use / command limitation / something difficult or confusing More information / solutions
2 You are not currently configured to use layer schemes. To change this use the "APS-CONFIG" command and go to the section titled "Layer Control". More information / solutions
3 Cannot find APS-PAT.TXT file. More information / solutions
4 Could not find "APS-CONFIG.LSP/.FAS". Verify the "Software" and "Software\Custom" folders are in the acad search path. More information / solutions
5 Sorry, "Arcs/Blocks/Circles....etc" cannot be used for this selection. More information / solutions
6 Cannot find \"APS-AT.MNU\". Active toolbars cannot be loaded. More information / solutions
7 The "APS-CMD01.LSP/.FAS" file could not be found in the current Acad path. This may be due to a missing network path or AutoCAD "Support file search path" entry. The "Support file search path" to the APS files needs to be restored or APS reinstalled. More information / solutions
8 *ERROR* Cannot find the "APS.CFG" configuration file for input. APS commands will use default configuration values. Type "APS-CONFIG" at the command prompt to run the configuration utility. More information / solutions
9 The <filename> file could not be found in the current Acad path. This may be due to a missing network drive or AutoCAD "Support file search path". The "Support file search path" to the APS files needs to be restored or APS reinstalled. More information / solutions
10 *ERROR* Cannot find "APS-CONFIG.LSP/.FAS" for input. APS Configuration utility has not been loaded. More information / solutions
11 Could not locate "SHRTCUTS.LSP". Shortcut key commands were not loaded. More information / solutions
12 Could not locate "CMDNAMES.LSP". Standard command names were not loaded. All Software commands will begin with "APS-" More information / solutions
13 APS files cannot be found in the current Acad path. This may be due to a missing network path or the files being corrupted. The "Support file search path" to the files needs to be restored or APS reinstalled. More information / solutions
14 *ERROR* Cannot find "APS-BAS.MNU". The APS portion of the menu cannot be loaded. More information / solutions
15 *ERROR* Cannot find "APS-LS.MNU". The APS layer pulldowns cannot be loaded More information / solutions
16 *ERROR* Cannot find "APS-AT.MNU". The active toolbars cannot be loaded More information / solutions
17 All of the layers that are ON, UNLOCKED & NOT XREF DEPENDANT are configured as "No Plot" layers in the APS Configuration Utility. See "More Info" below. More information / solutions
18 *** Warning ***  The "<dwgname>.BAK" file is set to "read only". This drawing cannot be saved until this backup file is either set to "read" or erased.    *** Save failed *** More information / solutions
19 Could not find an abbreviation definition file, omitting schedule legend. More information / solutions
20 This command (VPFL) requires that you use layer schemes to control layers. More information / solutions
21 This command (XRFL) requires that you use layer schemes to control layers. More information / solutions
22 Could not locate "APS-MFIL.DWG". Menu status cannot be saved. More information / solutions
23 A layer scheme file (*.LYR) has not been specified in this drawing or could not be located. The default layer scheme file was also not found. Use the "APS-CONFIG" command to specify a default layer configuration file. More information / solutions
24 Cannot find APS-MNU.TXT file. More information / solutions
25 Cannot find APS-TEMP.LAS file. More information / solutions
26 PLINE selected is not a "closed" PLINE More information / solutions
27 Could not find a keynote definition file More information / solutions
28 Keynote list font size specified is too large More information / solutions
29 Could not find a material key definition file More information / solutions
30 Material key font size specified is too large More information / solutions

Is there anything that you find confusing or difficult? Please let us know so we can help!

Copyright 2006 KLH Software, Inc. All rights reserved. Reproduction or copying of content or images is prohibited.
Legal Notices and Trademarks | Privacy Policy | Contact KLH Software
Autodesk, AutoCAD, AutoCAD Architectural Desktop, AutoLISP, and Visual LISP are either registered trademarks or trademarks of Autodesk, Inc., in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders.